Fiberglass Pipe Insulation|Spray Foam Insulation Kits

Make your Home Energy Efficient

Make your Home Energy Efficient

Focusing on space heating and water consumption is an important consideration in making your home become more energy efficient. Usually, so much energy is being consumed by a house through these. To reduce energy consumption, some of these basic steps have to be taken:

1. Insulating Your Water Heater

Lowering your water heater’s thermostat setting may be helpful when you always have plenty of hot water. This approach to saving energy benefits most electric heaters. If you want your water heater to conform to your water usage schedule, you may also utilize timers. They prevent the water heater from trying to maintain hot water during periods when it is never used. Furthermore, you can add to the insulation of water heaters. You can do so by wrapping the insulation horizontally around the unit using duct tape to seal the seams where they meet. Then, make cut-outs to leave the thermostat, controls and drain faucets exposed. If you have an electric water heater, cut a cap of insulation to fit the top. Provide slits for the water inlet and outlet pipes. If you have a gas water heater, do not cover the burner access or the flue collar. Leave about two inches of exposed area around the flue collar then tape any remaining joints and seams.

2. Pipe Wrapping

You should insulate water pipes that pass through unheated areas and run under your house from an unheated utility room. If you don’t insulate hot water pipes, they will easily lose heat and cause your water heater to work harder. Although cold water pipes are more resistant to those, insulating them can also prevent sweating and dripping in heated areas, or freezing in unheated areas. Easy to use, pre-formed foam pipe insulation sleeves are easily available in most hardware stores.

3. Replace Furnace Filters

Furnace filters will have to work harder when they are clogged because this will reduce airflow through the heating and cooling systems. Overheating and premature compressor damage in air conditioning systems are usually caused by severely clogged filters. Therefore, you need to check your furnace filter monthly. If you are going to go to the trouble to pull it out and look at it, you might as well go ahead and replace it in the process.

4. Cover the Windows and Seal the Doors

A significant chunk in most heating bills is due to heat lost through windows and doors. An estimation from several studies states that loss through windows alone could account for up to 35 percent of heating bills. To determine where drafts are, you need to check around windows and doors with a candle or a light piece of thread on a windy day. This will reveal problem areas in need of immediate attention. Afterwards, remove and replace damaged caulk and weather-stripping. If you want to save on costs, there is an inexpensive method of weatherizing windows that involves attaching thin, clear plastic film to the window trim inside of the house using two-sided tape. The film is then stretched tight using heat from a blow dryer to remove wrinkles and creases. Decorating your windows with closed shutters, window shades, blinds, curtains and lined draperies also helps. All of these contribute to energy savings by helping to insulate windows.

 

Consider some of these sites Eco-Friendly Castlegate Real Estate , Castlegate Homes for Sale with Pools and Castlegate Rental Property for more homes for sale suggestions.


Article from articlesbase.com

Thermwell Products S10XB/6 Foam Pipe Insulation 6′ (Pack of 70)

  • “THERMWELL” FOAM PIPE INSULATION
  • 6′
  • Black
  • Tubular Polyethylene Foam Pipe Insulation
  • Pre-slit insulating polyethylene foam

6′, Black Tubular Polyethylene Foam Pipe Insulation, Self Sealing, 3/8″ Wall Thickness, For Use On 1/2″ Copper Pipe Or 1/4″ Iron Pipe, Bulk.

Price: $ 75.99

Please check out my brothers page at www.youtube.com

Other articles you might like;

25 comments on Make your Home Energy Efficient

  1. thejulian280 says:

    how did u build this how old are u this must of too hours please answer all my questions and please comment back

  2. rockchief1 says:

    What’s the material for the loopings?

  3. DarkKnuckles100 says:

    best part o:oo to 2:30

  4. mikkokoivunut says:

    @123585919 That’s a marble chute. Look at garage sales or places like goodwill or thrift stores.

  5. 123585919 says:

    Hey! this is awesome! My friends and I are doing a physics roller coaster and we were wondering where you got that colorful plastic thing y’all used at the end!?

  6. ipthenry says:

    Wow that is pretty damn beast

  7. buttsheeve says:

    I call that stuff donkey dick

  8. Zone5052 says:

    Sweeeeeeet!!!!!!

  9. MidnightxSkye says:

    :P Lol’d. Major loopage. XD

  10. CheckTwilight says:

    this is awesome
    im working on one in my dining room :p

  11. juliangorring says:

    holy ( beep ) how did u make that?!?!?!?
    teach me teach me plz plz PLZ comment back

  12. wegetmoney1 says:

    sick!!!!!!!

  13. XXXXXAlessioXXXXX says:

    very funny

  14. QuakersHockey12 says:

    SWEET !!!!

  15. mikkokoivunut says:

    cool!!! i’ll try to make another one soon

  16. strpwnage68 says:

    mikkonokivunnt awesome video i also have made a ton of roller roaster out of inslater keep on making more pretty plz and tyvm!!

  17. riiguy12 says:

    sweet!!

  18. mywebkinzlover99 says:

    SWEET

  19. MinnesotaWildFanatic says:

    sweet!

  20. Sharksofsanjose says:

    thast justing FING CRAZY XD nice job

  21. Coast2Coast49 says:

    Sweet

  22. mikkokoivunut says:

    yes, worth the effort, but it stinks when you MOM makes you take it down 1 min after filming the video……you don’t wanna know what happend

  23. habsrule7433 says:

    wow! impressive! worth all that effort in the end

  24. mikkokoivunut says:

    yep, about 6 hours in total

  25. habsrule7433 says:

    That was cool! Must have taken a while to get it set up and working.

Leave a comment